自适应无网格法在生物涂层接触问题中的应用

自适应无网格法是针对有限元法无法求解或者不易求解的复杂问题,利用无网格法节点排布灵活、易于增删节点、便于自适应分析等优点发展起来的. 在对自适应无网格法理论基础和发展进行总结基础上,采用基于应变能梯度的自适应无网格—— 有限元耦合方法,对等离子喷涂制备的HA 生物涂层材料的无摩擦接触问题进行分析,对制备的两种不同厚度的生物涂层材料进行求解,分别给出了von Mises 应力分布云图. 结果表明,自适应无网格法能较好地应用于生物涂层接触问题中.     

非一致性界面热流固耦合作用的整体求解

提出了非一致性界面热流固耦合作用整体求解的一种方法．热流体求解基于Boussinesq假设和不可压缩的Navier-Stokes方程．流体区域的运动采用任意Lagrange-Euler（ALE）方法．拟固体元方法实现流体区域的变形．使用几何非线性的热弹性动力学描述固体运动．为了保证界面处应力和传热的平衡,采用了基于Gauss积分点的数据交换方法,对热流固耦合最终形成的强非线性方程实现整体求解．数值实例分析表明该方法的健壮性和有效性．     

防止温度应力下海底管线发生整体屈曲的工程措施研究

为减小油气输送难度和避免原油固化,石油、天然气通常在高温高压下输送．输送过程中的高温和高压导致海底管线中产生较大的附加应力,附加应力的不断累积造成管线发生整体屈曲．对于埋地的海底管线通常会产生竖向屈曲大变形而影响使用甚至破坏．因此,需对有可能产生整体屈曲的管线采取工程防护措施．结合我国海洋工程中管线常用的铺设及保护措施,对处于保护状态下管线由温度应力引起的整体屈曲特性进行理论分析和数值推导,对沟槽保护、沟槽掩埋保护以及压块保护措施的有效性进行了系统分析和对比．     

Monolithic approach to thermal fluid-structure interaction with nonconforming interfaces

This paper presents a monolithic approach to the thermal fluid-structureinteraction(FSI) with nonconforming interfaces.The thermal viscous flow is governedby the Boussinesq approximation and the incompressible Navier-Stokes equations.Themotion of the fluid domain is accounted for by an arbitrary Lagrangian-Eulerian(ALE)strategy.A pseudo-solid formulation is used to manage the deformation of the fluid do-main.The structure is described by the geometrically nonlinear thermoelastic dynamics.An efficient data transfer strategy based on the Gauss points is proposed to guarantee theequilibrium of the stresses and heat along the interface.The resulting strongly coupledset of nonlinear equations for the fluid,structure,and heat is solved by a monolithicsolution procedure.A numerical example is presented to demonstrate the robustness andefficiency of the methodology.     

匀强及非匀强磁场中Heisenberg XXX链的纠缠研究

研究了匀强及非匀强磁场中反铁磁体Heisenberg XXX链的近邻和次近邻纠缠.结果表明对基态情形,纠缠随磁场B变化呈现阶梯型结构,这可用来构建量子纠缠"放大器"或量子纠缠"开关".对有限温度情形,引进一非匀强磁场Bi=(-1)iB可以使近邻格点间纠缠在某些区域明显增大,而次近邻格点间纠缠则完全消失;同时引进非匀强磁场Bi=(-1)iB还可以使近邻格点纠缠的临界温度Tcn增大,且Tcn随B的增大而升高,这意味着我们可以通过调节B的大小而在任意温度下得到纠缠.     

Reverse Atom Transfer Radical Polymerization of MMA in the Presence of CaCO3/SiO2 Two-Component Composite Particles

Summary: We previously discovered that structurally well-defined polymer/inorganic composite particles, i.e., poly(methyl methacrylate) (PMMA)/CaCO₃/SiO₂ three-component composite particles, can be achieved via reverse atom transfer radical polymerization (ATRP), using 2,2′-azo-bis-isobutyronitrile as initiator and Cu^II bromide as catalyst. In the present study, the influence of the mass ratio of CaCO₃/SiO₂ two-component composite particles to methyl methacrylate (MMA) on the rate and behavior of the polymerization was studied in detail. The results illustrate that increasing the mass ratio of CaCO₃/SiO₂ two-component composite particles will decrease the overall rate of polymerization of MMA under standard reverse ATRP conditions. Thermal properties of the obtained well-defined particles were characterized and determined by thermogravimetric analysis (TGA). The results indicate that well-defined PMMA chains grafted on the surface of CaCO₃/SiO₂ particles were only degraded by random chain scission of C C linkages within the PMMA chain, which is different from the degradation of PMMA chains prepared via traditional radical polymerization. This difference is reasonably ascribed to the difference between the end groups of PMMA prepared via reverse ATRP and that via traditional radical polymerization, which has been confirmed by end group analysis measured by ¹H–NMR spectroscopy.     

Transparent conductive graphene films prepared by hydroiodic acid and thermal reduction

Transparent conductive graphene films are fabricated by the transfer printing of graphene aqueous dispersion followed by hydrohalic acids and thermal reduction. Results indicate that the graphene film reduced by hydroiodic acid （HI） reduction combined with thermal treatment shows a higher electrical conductivity than that reduced only by thermal treatment at the same transparency. A film with a sheet resistance of - 2400 D./sq at a transparency over 72% is obtained at a typical wavelength of 550 nm.     

紫外光固化自修复剂的微胶囊化及智能防腐蚀涂层的制备

利用在水相中原位生成的聚脲甲醛沉淀吸附在可见紫外光固化组份构成的油相表面,制备了包覆自修复剂的脲醛树脂（PUF）微胶囊. 光学显微镜及SEM表明,PUF微胶囊尺寸为118-663 μm,与PUF 形成过程中的搅拌速度有关. 在中等搅拌速度（600 r/min）时,可以得到最高的包覆率（97.52wt%）和产率（65.23wt%）. 将此微胶囊掺入水性聚氨酯乳胶中制成的涂层表面受损后,在紫外光照射下可以进行自修复,具有优异的金属防腐蚀性能.     

pH值对AZ31镁合金表面植酸转化膜在模拟体液耐腐蚀性能的影响

采用沉积的方法在镁合金AZ31表面制备植酸转化膜并研究了pH值的影响. 利用极化曲线和电化学阻抗谱方法测定其耐腐蚀性能,用扫描电子显微镜观察转化膜的表面微观结构,用能谱测定转化膜的组成元素. 在理论上通过热力学的方法分析最佳pH值. 植酸转化膜可以提高镁合金AZ31的耐腐蚀性能. 当植酸溶液的pH=5时腐蚀效率达到了89.19%,此时腐蚀电位正移了156 mV,腐蚀电流密度与没有处理的试样相比减小了约一个数量级. 热力学分析表明植酸转化膜的耐腐蚀性能不仅受植酸根离子和镁离子浓度的影响,也与氢气释放的速率有关.     

Dual solutions in boundary layer flow of a moving fluid over a moving permeable surface in presence of prescribed surface temperature and thermal radiation

An analysis of the heat transfer for a boundary layer forced convective flow past a moving permeable flat surface parallel to a moving fluid is presented. Prescribed surface temperature at the boundary is considered. A thermal radiation term in the energy equation is considered. The similarity solutions for the problem are obtained and the reduced ordinary differential equations are solved numerically. To support the validity of the numerical results, a comparison is made with the available results for some particular cases of this study. Dual solutions exist when the surface and the fluid move in the opposite directions.